Poster Finishing Equipment

Click here to visit the new VT Online Shopping Center! Buy Your Seal Supplies at Our New Online Shopping Center!
Seal® Image 600D laminator
For over 60 years Seal® has been a world leader in graphic finishing technology. Today, our full range of presses, ImageTM Roller Laminators, and Laminating Films and Adhesives are bringing new levels of performance, versatility and ease of use to image finishing. Whether you are working with electrostatic, ink jet, photographic or plain paper media, from basic dry mounting to E-stat image transfer for outdoor applications, Seal has a system to meet your needs.

Seal Image Roller Laminators offer large-format finishing of electrostatic, ink jet, photographic or plain paper media. They are available in a range of sizes and capabilities from the 41-inch pressure-sensitive units, such as the Image 400-S, to the fully loaded flagship of the line, the Image® 6000 Ultra - offering pressure-sensitive and heat-activated mounting and laminating, hot sealing and electrostatic image transfer up to 61 inches wide. All image laminators feature high-release silicone rollers, pneumatic pressure, independent electric heat with digital controls (heated units only), fast roller nip setting, easy-loading supply and take-up systems, and complete safety systems that meet or exceed international standards. Pictured is the new Seal Image 600 laminator.


The Image 600 is a medium- to high-volume laminator capable of heat-activated and encapsulating operations up to 55 inches (140 cm) wide, and pressure-sensitive mounting and laminating up to 61 inches (155 cm) wide. Performance proven features include:
  • High release silicone rollers for easy cleaning.
  • Pneumatic pressure adjustment with fine tune control for smooth, flat output.
  • Upper and lower heated rollers with electric heat and digital controls for even heating and accurate temperature control.
  • Dial-in roller height adjustment for fast, accurate nip setting.
  • Vacuum in-feed table with print guide for flat, wrinkle-free feeding of thin print media.
  • Cooling fans for smooth, flat output during encapsulating.
  • Two swing-out supply shafts (top and bottom) with brakes for easy loading and precise film tension adjustment.
  • Digital media roll easel for high-volume roll-to-roll laminating.
  • Submerged pull rollers for maximum performance during hot sealing and fast application change-over.
  • Automatic upper take-up for removing release liners.
  • Foot control for hands free operation.
  • Comprehensive safety systems with emergency stops and electric eyes.

  • CE and ETL approved.

    Seal Products Inc. 
    550 Spring St.
    Naugatuck, CT 06770-9985

    Technical Specifications Image 600
    Catalog Number IT600D
    Maximum working width 55 in. (140 cm) hot or 61 in. (155 cm) cold
    Maximum roller speed 10 fpm (304.8 cm,min)
    Maximum roller temperature 250°F (121°C)
    Maximum air pressure 125 psi
    Maximum roller opening 1 1/8 in. (29 mm)
    Roller surface construction High release silicone coated
    Supply shaft capacities 3 in. (7.6 cm) I.D. cores
    Maximum substrate thickness 1 in. (2.54 cm)
    Dimensions 78w x 32d x 50h in.
    (198w x 81d x 127h cm)
    Net weight 550 lb. (251 kg)
    Shipping weight 850 lb. (389 kg)
    Mechanical requirements 2 CFM compressed air @ 100 psi
    0.25 in. (0.6 cm) ID flexible line

    Air compressor supplied with models shipped to No. & So. America only.

    Electrical requirements, US & CAN  200-240 VAC, 50-60 Hz, 
    single phase, 30 Amp
    Electrical requirements, Intl. 380-415 VAC, 50-60 Hz,
    three phase, 15 Amp, 4-wire plus earth (grnd.)
    Maximum power consumption 7,200 Watts

    Image® 62 Plus


    The easy route to a big finish -- the Image 62 Plus offers new operators an uncomplicated approach to post-print finishing. Ultimately user-friendly, the Image 62 Plus is ideal for mounting, laminating and encapsulating images up to 61 inches (155 cm). Its versatile temperature range accommodates both low temperature heat-activated films for ink jet prints, and higher temperature polyester films for e-stat and photographic images. The Image 62 Plus is an excellent mid-range laminator that meets your post-print finishing needs without finishing your budget.

    · Touch pad control panel with pre-programmed temperature, speed and substrate settings.
    · Automatic front and rear take-up shafts for release liner removal.
    · Swing-out in-feed table for fast easy material webbing.
    · Swing-out supply shafts with auto-grip for easy loading and positioning of films.
    · Silicone rollers for effortless cleaning.
    · Simple film tension adjustment.
    · L.E.D. setting indicators.
    · Roll-to-roll media feed (optional).
    · Built in cooling fans for smooth output during hot encapsulating operation.
    · Antistatic pull rollers that minimize static charge build-up and insure consistent film tension for a flat, even finish.
    · Accurate electric temperature control for even heating.
    · Sturdy frame with casters and leveling feet.
    · Quiet motor operation.
    · Foot control for hands-free operation.
    · Extensive safety systems with emergency stops, electric eyes and proximity alarms.
    · Meets international safety standards.



    Control Panel
    Touch pad control with predefined settings for temperature, speed and substrate thickness make the Image 62 Plus extremely easy to use.


    Auto-Grip Shafts
    Swing out supply shafts with unique auto-grip feature means easy loading and positioning of films.


    Media Feed
    Optional media feed, combined with the Image 62 Plus' rear take-up shaft, affords roll-to-roll laminating for improved production throughput.

    Technical Specifications Image 62 Plus
    Catalog Number US,Canada: 60265
    International, three phase: 60252
    Maximum working width 62 in. (155 cm)
    Maximum roller speed 6 fpm (1.8 mpm)
    Maximum roller temperature 250°F (120°C)
    Maximum roller opening 1 in. (2.54 cm)
    Roller surface construction High release silicone coated
    Supply shaft capacities 3 in. (7.6 cm) I.D. cores
    Dimensions 86.6w x 30d x 48h in.
    (220w x 76.2d x 122h cm)
    Net weight 1153 lb. (530 kg)
    Shipping weight 1263 lb. (580 kg)
    Electrical requirements  3N/PE-200-250 VAC, 50/60 Hz, 25 A
    1N/PE-200-250 VAC, 50/60 Hz, 32 A
    Maximum power consumption 7,000 Watts

    Info Request.GIFRequest More Information

    Line of lights

    [Home| Corporate |News |Products |Support |Hardware Solutions |Image Director Software|Send Us Email]

    Emailed.gifIf you have comments or suggestions,
    email us at
    Or, Call us at 1-800-545-0378